[CUBE] problem installing JAG

[Marty Levenson]

I'm thinking of installing 10.1 and then updating that to JAG...see if that
works. I did have 10.1 working before, but uninstalled it due to some
crashes...thought I would start fresh with Jag.
Thanks for your replies!
Marty

> From: Thubten Kunga <Kunga at FutureMedia.org>
> Reply-To: "Cube List" <Cube at lists.themacintoshguy.com>
> Date: Sat, 11 Jan 2003 16:54:18 -0800
> To: "Cube List" <Cube at lists.themacintoshguy.com>
> Subject: Re: [CUBE] problem installing JAG
> 
> Should work on an empty partition. It's big enough right? Could be a
> problem with the optical drive. I really don't have any other
> suggestions. Anybody else here want to pitch in and help Marty get his
> Jaguar UP?
> 
> On Saturday, January 11, 2003, at 04:40  PM, Marty Levenson wrote:
> 
>> No, the installer worked on another computer, so the cd is ok.
>> The Disk utility says the partition is good. Not sure how you check
>> the HD
>> boot blocks...which menu?
>> Am I right it should install on an empty partition...dsoesn't need OS 9
>> there for classic? (OS 9.2.2 is running fine on a different
>> partition...)
>> 
>> Thanks again! Marty.
>> 
>>> It could be a defective install CD. Any clue that the HD has problems?
>>> Did you run the Disk Utility Utility from the install CD to make sure
>>> the HD boot blocks are all in order? You open it from the menu (not
>>> obvious that it's there).
>>> 
>>> k
>>> 
>>> On Saturday, January 11, 2003, at 03:40  PM, Marty Levenson wrote:
>>> 
>>>> yes...full install version.
>>>>> 
>>>>> The Jaguar is the full install version not the upgrade version?
>>>>> 
>>>>> k
>>>>>> Thanks - but yes, the firmware is up-to-date....also, I am running
>>>>>> OS
>>>>>> 9.2.2
>>>>>> and have 1 gig RAM.
>>>>>>> 
>>>>>>> Have you ever run the G4 firmware update 4.1.9?
>>>>>>> 
>>>>>>> Cube Support: http://www.info.apple.com/usen/g4cube/
>>>>>>> 
>>>>>>> Cube Firmware Update 4.1.9:
>>>>>>> http://docs.info.apple.com/article.html?artnum=75129
>>>>>>> 
>>>>>>> k
>>>>>>> On Saturday, January 11, 2003, at 02:49  PM, Marty Levenson wrote:
>>>>>>> 
>>>>>>>> Dear List,
>>>>>>>> I'm still unable to install Jag on my 450 cube. The installer
>>>>>>>> keeps
>>>>>>>> quitting
>>>>>>>> early on in the installation...not always at the same point.  I
>>>>>>>> just
>>>>>>>> installed it on my girlfriend's dual 450 tower without a problem.
>>>>>>>> Any
>>>>>>>> suggestions? When it quits it goes to terminal mode and says
>>>>>>>> roughly:
>>>>>>>> "unexpected shutdown (error type 0) restart."
>>>>>>>> 
>>>>>>>> Thanks,
>>>>>>>> Marty (Vancouver)
> 
> 
> ----------
> Check out the Cube email list FAQ
> http://www.themacintoshguy.com/lists/Cube.html
> 
> To unsubscribe, E-mail to: <Cube-off at lists.themacintoshguy.com>
> To switch to the DIGEST mode, E-mail to
> <Cube-digest at lists.themacintoshguy.com>
> Need help from a real person? Try.  <Cube-request at lists.themacintoshguy.com>
> 
> ----------
> $14.99 Unlimited Nationwide Mac Dialup and Mac Web Hosting from your Mac ISP
> Serious Mac Internet Solutions From NineWire!   http://macinternetaccess.com
> 
> T3Hub  |  3 Port USB Hub weighs less than an ounce!
> Dr. Bott|   <http://www.drbott.com/prod/T3Hub.html>
> 
> Cyberian   | Support this list when you buy at Outpost.com!
> Outpost    | http://www.themacintoshguy.com/outpost.shtml
> 
> ADC Extension | Extend the built in cable of your flat panel by 10 ft.
> Dr. Bott    |    <http://www.drbott.com/prod/ADCExtension.html>